Transmission, Clutch, Sprocket
Clutch, Gears, Sprockets, Shafts, Spacers
-
1972 to 1974 Husqvarna SHIFT SHAFT for Low Shift Shaft Location 16-10-594-01 NOS
$35.00
-
1974-1979 Husqvarna 12T COUNTER SHAFT SPROCKET 12 Tooth, 8 Spline 16-12-471-03
$37.99
-
1969-1988 Husqvarna "PBI" 53 TOOTH ALUMINUM REAR SPROCKET 53T Dual Bolt Pattern
Out of stock
-
CIRCLIP SNAP RING SPROCKET HOLDER 1974 to 1979 NEW 73-53-122-01
$3.99
-
1974-1979 Husqvarna PBI 14T COUNTER SHAFT SPROCKET 14 Tooth, 8 Spline 16-12-471-05
$34.00
-
1970 to 1974 Husqvarna LOCK PLATE, CLUTCH SPRINGS, 4 Required 16-11-113-01 NOS
$2.99
-
1973-1979 Husqvarna 4th Gear on Layshaft 24 teeth 16-12-409-01 NOS
$29.00
-
1969-1988 Husqvarna PBI 52 TOOTH ALUMINUM REAR SPROCKET 52T Dual Bolt Pattern
Out of stock
-
CIRCLIP SPROCKET 1980 ON AND TRANSMISSION 1974 to 1988 NEW 73-53-126-00
$3.50
-
Husqvarna Layshaft for Splined Sprocket 16-12-470-01 NOS
$49.99
-
1980-1988 Husqvarna PBI COUNTER SHAFT SPROCKET 14 Tooth, 12 Spline 16-12-693-05
$27.00
-
1974-1979 Husqvarna NOS 12T COUNTER SHAFT SPROCKET 12 Tooth, 8 Spline 16-12-471-03 NOS
Out of stock
-
1966 to 1971 SPROCKET 4mm WOODRUFF KEY NOS 16-12-927-01
$4.30
-
1980-1988 Husqvarna SPROCKET SPACER USED VG 16-12-353-01
Out of stock
-
DID CHAIN ERT3 120 LINK WITH MASTER LINK
$109.00
-
1966 to 1975 Husqvarna BUSHING Behind Clutch 16-11-962-01 NEW
$39.00
-
BORG 299523001 280163601
Out of stock
-
1972 to 1974 Husqvarna SHIFT LEVER USED 16-10-940-02 NOS
Out of stock
-
Husqvarna CHAIN GUIDE SIDE PANEL RUB PLATES 15-10-757-01 Sold as Each
$3.00
-
1980-83 2nd Gear on L/S 16-12-347-01 NOS is New Old Stock
$38.99
-
1987 1988 HUSQVARNA CLUTCH PRESSURE PLATE 6 SPRING TYPE USED VG 16-14-416-01
Out of stock
-
1987-88 HUSQVARNA CLUTCH PLATE SET BARNETT 430 500 250 16-14-408-01 16-14-409-01
Out of stock
-
1975-1982 Husqvarna Main Clutch Shaft 15 Teeth 6 Spd 16-12-477-01 NOS
$39.99
-
1973-1982 Husqvarna 5th Gear on L/S 22 teeth 16-12-410-01 NOS
$21.99
-
1975-1979 Husqvarna 2nd Gear on L/S 28 teeth Flat Back 16-12-597-01 NOS
$19.99
-
1969-1974 Husqvarna OEM TAPERED 10T COUNTER SHAFT SPROCKET 10 Tooth 16-12-994-05
$47.99
-
1980-1988 Husqvarna NOS COUNTER SHAFT SPROCKET 12 Tooth, 12 Spline 16-12-693-03
$37.00
-
1972-1975 Husqvarna 125CR Gear 31 teeth 1st on L/S 13mm Thick Dished Back 16-12-406-01 NOS
$19.99
-
WIRE CIRCLIP EXHAUST END 15-14-954-01 FITS Multiple WR Models 76mm 3" DIAMETER
$4.50
-
CIRCLIP EXHAUST END 15-14-954-01 FITS Multiple WR Models 79mm 3 1/4" DIAMETER
$4.50
-
CIRCLIP EXHAUST END 28-22-058-02 FITS 1974 TO 1976 CR 62MM 2 1/2" DIAMETER
$4.50
-
1974-1979 Husqvarna NOS 10T COUNTER SHAFT SPROCKET 10 Tooth, 8 Spline 16-12-471-01 NOS
Out of stock
